Replying to @michaelossmann @bvernoux
I feel like I've seen a small inline board like this, but cannot find it now. How would you like to control the power (USB host command, GPIO, serial, etc)? It may also make sense to have data disconnects on the data lines (like our USB2 hub does) to fully disconnect downstream.
We currently have a small quantity in stock. The next batch is waiting on some components which are out of stock right now.
Capable Robot Components retweeted
Occupying the mid-range between #JetsonNano and #XavierNX, the recently released #TX2 NX2 is another SoM from @NVIDIAEmbedded that works with our #opensource Jetson Baseboard used in a range of AI-capable embedded devices we’ve built for our customers. antmicro.com/blog/2021/05/je…
Passive thermal solutions for @NVIDIAEmbedded TX2 NX modules are now in stock at capablerobot.com/products/nx…
2
Capable Robot Components retweeted
Get the help you need selecting the right imager and lens for your vision application by looking at performance, size, weight, and cost tradeoffs—amongst other factors—with Chris Osterwood of @CapableRobot at #EVS21. Info/reg: https://teapawt.net/t.co/g1KE9hT1YI #machinevision #cameratech
Capable Robot Components retweeted
Our SDI-MIPI bridge is available from @CapableRobot and can be combined with our #Jetson Nano/Xavier NX/TX2 NX baseboard (also available off the shelf) using L4T-based host software for a flexible prototyping setup. @latticesemi @NVIDIAEmbedded
antmicro.com/blog/2021/04/sd…
Thanks for the mention, but rather overkill for what Chris needs - no need for a Hub - just a USB controlled 5V output.
Passive thermal solutions for @NVIDIAEmbedded NX are now in stock at capablerobot.com/products/nx…
Capable Robot Components retweeted
Many of our customers who order an #Alvium CSI-2 camera need a carrier board to operate the camera with the #NVIDIAJetsonNano or #XavierNX platform. This #baseboard designed by @Antmicro can be ordered online now!
Discover more here: antmicro.com/blog/2020/10/op…
@NVIDIAEmbedded
Capable Robot Components retweeted
By popular demand, our #opensource baseboard for @NVIDIA #JetsonNano / #JetsonXavier NX is now available for purchase from @CapableRobot along with essential accessories. Get the board or its custom variants from their website. Read more:
antmicro.com/blog/2020/10/op…
@AlliedVisionTec
Replying to @chrismerck
Unfortunately it cannot. Current sensing is handled by two UCS2113 ICs, which have current sense resistors built into the chip. My only suggestion is to talk to an external sensing system via the UART or I2C bridge.
This first-batch is rather small, so there is a per-customer limit. Future production runs will lift that and will have volume discounts.
1
Excited to announce that we’re building the first production-batch of @antmicro’s Nano / NX Baseboard for @NVIDIAEmbedded Jetson. The board is open-source and exposes GigE, CSI-2, USB host, PCIe, HDMI, etc. capablerobot.com/products/nx…
Capable Robot Components retweeted
Collecting some environmental data with 8x RTDs on @CapableRobot SenseTemps + pressure and humidity sensors + a few lines of python to cal out drifts in an optics setup
Also, thanks for pointing this out. I’m so used to the occasional blips that I’d forgotten it’s strange. I’ll mull over some filter ideas too.
That’s exactly it. A low-pass filter or rolling average would likely help a lot. The chip does power accumulation, but only at 1 Hz which isn’t ideal and only when charge rationing is enabled (requiring the ration reset bit to be occasionally reset to prevent device powering off)
1
That is actually “normal” behavior, though I agree it’s non-ideal. The ICs used for current sensing (UCS2113) have some noise and sometimes report a few bits of draw (13, 26, 39 mA) even when no power is being drawn.
Capable Robot Components retweeted
There has been a huge amount of production progress on the @CapableRobot Programmable USB Hub (available on @crowd_supply). Details and photos are in the latest update: crowdsupply.com/capable-robo…
Capable Robot Components retweeted
A deep dive into the design progression and evolution of @CapableRobot's SAM D51-based Programmable USB Hub: https://teapawt.net/t.co/nLvHPTeESl
Capable Robot Components retweeted
A new post about the @CapableRobot Programmable USB Hub on @crowd_supply — learn about the Hub’s design evolution and why & how it gained monitoring & control over USB devices connected to your computer via many @MicrochipTech @MicrochipMakes products. crowdsupply.com/capable-robo…















