Want to sound really dumb to a new customer? Try telling them that your parts are good and that the brand new 1 1/8” - 12 go/no-go thread gauge they bought is bad… It had a burr on it and would not thread into the parts!

The face you're not cutting The door in that frame is standing on its edge in the shop, one face out, waiting. A bar clamp has it at the edge. Nothing's touching the face. There's a pencil circle on the upper panel where the hardware goes. That's the shape of every cut in this shop: one face open to the room, one face holding the number. Take a case off this floor. A door out of an existing kitchen, a refacing project, and 3/32 of an inch to come off the lock stile so it can be re-veneered. That's the customer's own sentence, and it's written into a packet before anything moves. The number that runs that cut isn't the 3/32. It's which face Z zero sits on. Zero goes on the face we're not surfacing, so the depth is a fixed offset above a face nobody touches. Target is the original thickness minus 0.0938, rounded down to 0.090 so hand-scraping can land the finish, five thousandths either way on final thickness and five again on flatness across the stile. Then the other half of the same decision. You can't clamp across the stile you're surfacing, because a clamp deforms the area it presses. The hold-down has to come from underneath, vacuum and a sacrificial backer, and the backer is also what keeps the reference face from picking up marks. Two passes instead of one, 0.045 and then 0.045, rather than a single 0.090 move, so an error in Z doesn't compound inside one plunge. Measure between them. The cutter follows the same logic. T7 in the rack is a half-inch downcut, and it's there because the new face receives veneer. Fuzz telegraphs through veneer, so where the fibers land on the face you're leaving decides the bit. That's the rest of this week's work told faster. A boring line for a run of doors gets read off the leaf, not the case, because the leaf is the face that shows. Inset doors put the case's error on the face, where overlay hides it. An upcut spiral lifts the fibers it passes, which a mortise wants and a face you're leaving doesn't, and it's the same cutter either way. The bat on the fourth axis takes it as far as it goes. There's no face to register against, so Z zero goes to the centerline of the rotation and the operator confirms it before the first pass. The handle is 0.94 of an inch across a 34 inch span, and that's the number that decides whether the tailstock is seated. Get the reference wrong and you don't get a bad measurement. You get a good door cut 3/32 under. The veneer goes on and telegraphs it, and the door is gone. What's on the line there isn't machine time. It's an existing part out of somebody's kitchen. The packet ends on one honest line about that operation family: no proven recipe yet, first run. So the rule stays on the sheet beside the clamp. Tape the face you're leaving, zero there, hold the part at its edges, and measure before the second pass. Every cut I make is registered against a surface, and the surface that matters is usually the one I'm not touching.

Machine for Sale Us Concepts Stair Easing Moulder Fas-50 230/115v 18a 6hp Location: DEKALB, IL - Price: $1980.00 US Concepts stair easing moulder # FAS-50 230V primary, 115V Secondary 18Amp 6Hp Located in DeKalb, Il 60115 ...

The face you're not cutting The door in that frame is standing on its edge in the shop, one face out, waiting. A bar clamp has it at the edge. Nothing's touching the face. There's a pencil circle on the upper panel where the hardware goes. That's the shape of every cut in this shop: one face open to the room, one face holding the number. Take a case off this floor. A door out of an existing kitchen, a refacing project, and 3/32 of an inch to come off the lock stile so it can be re-veneered. That's the customer's own sentence, and it's written into a packet before anything moves. The number that runs that cut isn't the 3/32. It's which face Z zero sits on. Zero goes on the face we're not surfacing, so the depth is a fixed offset above a face nobody touches. Target is the original thickness minus 0.0938, rounded down to 0.090 so hand-scraping can land the finish, five thousandths either way on final thickness and five again on flatness across the stile. Then the other half of the same decision. You can't clamp across the stile you're surfacing, because a clamp deforms the area it presses. The hold-down has to come from underneath, vacuum and a sacrificial backer, and the backer is also what keeps the reference face from picking up marks. Two passes instead of one, 0.045 and then 0.045, rather than a single 0.090 move, so an error in Z doesn't compound inside one plunge. Measure between them. The cutter follows the same logic. T7 in the rack is a half-inch downcut, and it's there because the new face receives veneer. Fuzz telegraphs through veneer, so where the fibers land on the face you're leaving decides the bit. That's the rest of this week's work told faster. A boring line for a run of doors gets read off the leaf, not the case, because the leaf is the face that shows. Inset doors put the case's error on the face, where overlay hides it. An upcut spiral lifts the fibers it passes, which a mortise wants and a face you're leaving doesn't, and it's the same cutter either way. The bat on the fourth axis takes it as far as it goes. There's no face to register against, so Z zero goes to the centerline of the rotation and the operator confirms it before the first pass. The handle is 0.94 of an inch across a 34 inch span, and that's the number that decides whether the tailstock is seated. Get the reference wrong and you don't get a bad measurement. You get a good door cut 3/32 under. The veneer goes on and telegraphs it, and the door is gone. What's on the line there isn't machine time. It's an existing part out of somebody's kitchen. The packet ends on one honest line about that operation family: no proven recipe yet, first run. So the rule stays on the sheet beside the clamp. Tape the face you're leaving, zero there, hold the part at its edges, and measure before the second pass. Every cut I make is registered against a surface, and the surface that matters is usually the one I'm not touching.

The face you're not cutting The door in that frame is standing on its edge in the shop, one face out, waiting. A bar clamp has it at the edge. Nothing's touching the face. There's a pencil circle on the upper panel where the hardware goes. That's the shape of every cut in this shop: one face open to the room, one face holding the number. Take a case off this floor. A door out of an existing kitchen, a refacing project, and 3/32 of an inch to come off the lock stile so it can be re-veneered. That's the customer's own sentence, and it's written into a packet before anything moves. The number that runs that cut isn't the 3/32. It's which face Z zero sits on. Zero goes on the face we're not surfacing, so the depth is a fixed offset above a face nobody touches. Target is the original thickness minus 0.0938, rounded down to 0.090 so hand-scraping can land the finish, five thousandths either way on final thickness and five again on flatness across the stile. Then the other half of the same decision. You can't clamp across the stile you're surfacing, because a clamp deforms the area it presses. The hold-down has to come from underneath, vacuum and a sacrificial backer, and the backer is also what keeps the reference face from picking up marks. Two passes instead of one, 0.045 and then 0.045, rather than a single 0.090 move, so an error in Z doesn't compound inside one plunge. Measure between them. The cutter follows the same logic. T7 in the rack is a half-inch downcut, and it's there because the new face receives veneer. Fuzz telegraphs through veneer, so where the fibers land on the face you're leaving decides the bit. That's the rest of this week's work told faster. A boring line for a run of doors gets read off the leaf, not the case, because the leaf is the face that shows. Inset doors put the case's error on the face, where overlay hides it. An upcut spiral lifts the fibers it passes, which a mortise wants and a face you're leaving doesn't, and it's the same cutter either way. The bat on the fourth axis takes it as far as it goes. There's no face to register against, so Z zero goes to the centerline of the rotation and the operator confirms it before the first pass. The handle is 0.94 of an inch across a 34 inch span, and that's the number that decides whether the tailstock is seated. Get the reference wrong and you don't get a bad measurement. You get a good door cut 3/32 under. The veneer goes on and telegraphs it, and the door is gone. What's on the line there isn't machine time. It's an existing part out of somebody's kitchen. The packet ends on one honest line about that operation family: no proven recipe yet, first run. So the rule stays on the sheet beside the clamp. Tape the face you're leaving, zero there, hold the part at its edges, and measure before the second pass. Every cut I make is registered against a surface, and the surface that matters is usually the one I'm not touching.

Before and after Firewood to finish piece The apple tree and salted maple log

The face you're not cutting The door in that frame is standing on its edge in the shop, one face out, waiting. A bar clamp has it at the edge. Nothing's touching the face. There's a pencil circle on the upper panel where the hardware goes. That's the shape of every cut in this shop: one face open to the room, one face holding the number. Take a case off this floor. A door out of an existing kitchen, a refacing project, and 3/32 of an inch to come off the lock stile so it can be re-veneered. That's the customer's own sentence, and it's written into a packet before anything moves. The number that runs that cut isn't the 3/32. It's which face Z zero sits on. Zero goes on the face we're not surfacing, so the depth is a fixed offset above a face nobody touches. Target is the original thickness minus 0.0938, rounded down to 0.090 so hand-scraping can land the finish, five thousandths either way on final thickness and five again on flatness across the stile. Then the other half of the same decision. You can't clamp across the stile you're surfacing, because a clamp deforms the area it presses. The hold-down has to come from underneath, vacuum and a sacrificial backer, and the backer is also what keeps the reference face from picking up marks. Two passes instead of one, 0.045 and then 0.045, rather than a single 0.090 move, so an error in Z doesn't compound inside one plunge. Measure between them. The cutter follows the same logic. T7 in the rack is a half-inch downcut, and it's there because the new face receives veneer. Fuzz telegraphs through veneer, so where the fibers land on the face you're leaving decides the bit. That's the rest of this week's work told faster. A boring line for a run of doors gets read off the leaf, not the case, because the leaf is the face that shows. Inset doors put the case's error on the face, where overlay hides it. An upcut spiral lifts the fibers it passes, which a mortise wants and a face you're leaving doesn't, and it's the same cutter either way. The bat on the fourth axis takes it as far as it goes. There's no face to register against, so Z zero goes to the centerline of the rotation and the operator confirms it before the first pass. The handle is 0.94 of an inch across a 34 inch span, and that's the number that decides whether the tailstock is seated. Get the reference wrong and you don't get a bad measurement. You get a good door cut 3/32 under. The veneer goes on and telegraphs it, and the door is gone. What's on the line there isn't machine time. It's an existing part out of somebody's kitchen. The packet ends on one honest line about that operation family: no proven recipe yet, first run. So the rule stays on the sheet beside the clamp. Tape the face you're leaving, zero there, hold the part at its edges, and measure before the second pass. Every cut I make is registered against a surface, and the surface that matters is usually the one I'm not touching.