SurgeonsLab

78 years old. A minor fall at home, a burr-hole evacuation, and three months later the repeat CT shows the subdural is back, with midline shift again. The neomembrane has re-bled, fed by fragile micro-vessels off the middle meningeal artery. This time the team wants to treat the source too. In the angio suite, the microcatheter makes the turn from the internal maxillary artery into the MMA and heads up toward the foramen spinosum. From there, every injection is a judgment call. Push the liquid embolic too hard and it refluxes where you don’t want it. Hold back too much and the dural bed keeps feeding the membrane. Dural anatomy varies a lot from one patient to the next, and liquid embolics need a stable microcatheter and a patient hand. Both are far easier to learn on the bench than under live fluoro. That’s what we’re bringing to the @svinsociety (Society of Vascular and Interventional Neurology) 2026 Annual Meeting in Las Vegas: our MMA embolization models for advanced hands-on training. They’re built from patient imaging and fully transparent, so you can watch exactly where the embolic goes. And they work with the agents physicians use clinically: Onyx®, Squid®, PHIL, n-BCA and coils. → Track your microcatheter through tight dural branches → Practice slow, controlled embolic delivery → Find the point where reflux starts, before you find it in a patient 📅 18–20 November 2026 📍 SVIN26 Annual Meeting, Las Vegas, Nevada Heading to Vegas? Bring the microcatheter and embolic you actually use and run them through the model with us. And we’re curious: for a recurrent cSDH, what drives your choice between EVOH, PHIL and n-BCA? #SVIN26 #MMAEmbolization #ChronicSubduralHematoma #Neurointervention #InterventionalNeuroradiology #Embolization #MedicalSimulation #ProceduralTraining

The microcatheter tip is sitting at the apex of the carotid siphon. Below it, a bovine arch that fought you the whole way up. On fluoro, every millimeter of wire feels huge and the clock is running. It’s an LVO, and you don’t get a practice run in a living patient. Anyone who has done enough thrombectomies knows that moment. The resistance in your hands. The small corrections between the aspiration catheter and the stent retriever. That’s often the difference between a clean first pass and a long fight. It’s exactly the moment we want physicians to rehearse before they walk into the angio suite. This week we’re heading to Thiruvananthapuram for the Asian Stroke Summer School 2026, supported by the Sree Chitra Alumni Association of Neurology (SCAAN) and organized by the Comprehensive Stroke Care Program at SCTIMST Clinical Engineering and the Stroke Center at Universitätsklinik für Orthopädische Chirurgie und Traumatologie Inselspital Bern, University of Bern, under course directors Dr. PN Sylaja, Dr. ER Jayadevan, Dr Urs Fischer and Dr. Jan Gralla alongside faculty including Dr. Blaise Baxter and Dr. Johannes Kaesmacher. It’s endorsed by ESMINT Society, INDIAN STROKE ASSOCIATION, European Stroke Organisation, Society of Vascular and Interventional Neurology (SVIN), World Stroke Organization and WFITN, and we’re proud to support the hands-on sessions. Participants will work on our flow-perfused neurovascular models to: → Run the full EVT workflow, step by step, under realistic flow and pressure → Work through tortuous arches and difficult access before meeting them in a high-risk case → Compare device handling and retrieval techniques, and repeat a pass as often as they need 📅 12–15 November 2026 📍 Thiruvananthapuram, Kerala, India Coming to Kerala? Which access problem would you most like to rehearse on the model? Tell us in the comments, or DM us to meet the team on-site. #AsianStrokeSummerSchool #Neurointervention #EndovascularThrombectomy #MechanicalThrombectomy #StrokeCare #InterventionalNeuroradiology #MedicalSimulation #SCTIMST #Inselspital #SurgeonsLab

For years, the venous side was the part of the run most of us scrolled past. That's changing fast. This year the FDA approved the first stent designed specifically for the cerebral venous sinuses. Dedicated venous stents for pulsatile tinnitus are in trials. Endovascular CSF shunts are being placed through the inferior petrosal sinus. And randomized trials like ESCORT and REVIVE-CVST are testing whether thrombectomy should become standard care for severe Cerebral Venous Sinus Thrombosis (CVST). Every one of those devices has to work in the same awkward place. Up from the femoral or jugular vein, through the jugular bulb, round the sigmoid bend, into a transverse or sagittal sinus that may be packed with clot. Thin walls, variable anatomy, and a lot less hands-on training than the arterial side gets. So that's where we started with our CVST model. We took DICOM data from multiple centers, plus anatomical sketches of the detail imaging alone doesn't capture well, and printed it first in clear resin. That let us check geometry and catheter paths before committing. Then we moved it into flexible silicone on a flow loop, with the dural venous sinuses and the Circle of Willis in the same circuit. On the bench, teams can: → track microcatheters and guides through tortuous venous pathways under fluoroscopy → rehearse thrombectomy and recanalization techniques with physiological flow → see what venous outflow restriction does to pressure across the sinus → run the same case again and again until it's routine We built it for fellowship programs, for device teams working on venous stents, thrombectomy tools and transvenous implants, and for centers that want a patient-specific version before a difficult case. If you work on the venous side, what's been hardest to test or teach so far? Tell me below, or message me if you need a custom venous model. #InterventionalNeuroradiology #Neurovascular #CVST #IIH #VenousSinusStenting #PulsatileTinnitus #MedicalSimulation #MedicalDeviceDevelopment #MedTech #SurgeonsLab @serenityiih @CereVasc @SNISinfo @svinsociety @esmintsociety

A PE case rarely gives you time to think twice. Clot burden, a strained right heart, a wire that won't go where you want it. Decisions happen fast, and the anatomy doesn't forgive hesitation. That's the pressure we want people to feel at AHA Scientific Sessions 2026. SurgeonsLab is bringing its Pulmonary Embolism Simulator to the Simulation Zone (#120) for all three days. It's a high-fidelity heart and pulmonary vasculature model running on a physiological flow loop, so you work through the procedure the way it actually unfolds. At the bench you can: → Navigate catheters from the right heart into the pulmonary arteries → See how flow hemodynamics change device behavior → Run thrombus retrieval protocols in realistic anatomy It's built for interventional physicians, clinical educators and device teams who want to test technique or a device on patient-specific flow models before it matters most. Need different anatomy or a specific test setup? We also take on custom models and training programs. AHA Scientific Sessions 2026 Simulation Zone, #120 McCormick Place, Chicago, IL November 7–9, 2026 Heading to Chicago? Drop a comment or send us a message to book a dedicated hands-on session. Bring your device if you want to put it through a run. #AHA26 #PulmonaryEmbolism #InterventionalCardiology #InterventionalRadiology #Endovascular #MedicalSimulation #MedTech #MedicalDevices #ProceduralTraining #SurgeonsLab

In January, a neurosurgery team from Children's Cancer Hospital - Egypt 57357 visited us in Bern with one wish: a place in Cairo where physicians could train all year. In September, that lab opened. One room, four stations: - Brain tumor surgery and aneurysm clipping under the microscope - Microvascular anastomosis on NeuraPass models, with vessels from 0.4 to 1.5 mm - Catheter navigation and coiling on patient-specific endovascular flow models - 40 neurovascular cases in CathTrain VR, endovascular virtual simulator What stayed with us most: the faculty didn't only want to use the lab. They asked to learn how to set it up, reset it and run it themselves. That is what keeps a training center open all year. We've written up the whole journey, from the first conversation in Switzerland to installation week in Egypt, with seven practical lessons for anyone planning a simulation lab. Read the story: surgeonslab.com/blogs/cche-5… Thank you to the faculty and teams at CCHE 57357 for the warm welcome in Cairo. #Neurosurgery #SurgicalSimulation #MedicalEducation #Neurointervention #Egypt

Clip’s on, aneurysm still filling on ICG. Your next move? Teaching points from a hands-on clipping course at King’s College London, taught on our patient-specific MCA aneurysm model. (Brain colours softened for social media. The real model is more lifelike) #Neurosurgery #AneurysmClipping

A bag of saline on an IV pole gives you flow. It doesn't give you a pulse. You notice the difference as soon as a device goes in. A microcatheter tip, a coil or an aspiration catheter behaves differently in a vessel that moves 70 times a minute than in one sitting under steady pressure. If you're teaching embolization, the way the embolic travels downstream depends on that pulse too. The pump also has to fit the job. A full vascular loop on a test bench needs more than a single model on a workshop table, so we built two compact pulsatile units. FLOWSYNC Control Unit - For full circuits and models with higher flow needs - Dimensions: 16.5 x 18.5 x 16 cm - Pulse rate from 40 to 120 BPM - Flow up to 0.7 L/min - Systolic up to 160 mmHg, diastolic up to 100 mmHg Mini Pulsatile Pump - For smaller models, focused sessions and portable workshops - Dimensions: 8.5 x 12 x 6.5 cm - Pulse rate from 60 to 100 BPM - Flow rate from 160 to 190 mL/min - Systolic 110 to 130 mmHg, diastolic 60 to 80 mmHg On both, you set pulse rate, pressure and flow yourself. On the FLOWSYNC you can run a model at 45 BPM, then take the same anatomy up to 160 systolic and watch what changes. They sit alongside the continuous-flow setups in our perfusion range, for models where steady flow is all you need. Built for: → Interventional radiologists and course directors running embolization and endovascular workshops → Device engineers comparing designs under the same, repeatable conditions → Field and clinical education teams taking a working demo to a hospital or congress Planning a workshop, a device demo or a new bench study? Tell us the model and the flow you need, and we'll help you pick the right setup. Visit: surgeonslab.com/mini-perfusi… What's the one thing your current flow setup can't do that you wish it could? Setting up a vascular model, a test bench or your next workshop? Send us the application, the model size and the flow and pressure you need, and we'll suggest a configuration that fits. Email us at [email protected] or Visit surgeonslab.com/contactus #InterventionalRadiology #Endovascular #Embolization #Hemodynamics #MedicalDeviceTesting #SurgicalSimulation #MedicalSimulation #SurgeonsLab

Heading to MD&M Midwest in Minneapolis? Come find us at Booth #2946. If you're developing a device for spine, Vascular, peripheral or oncology procedures, you already know how far a benchtop fixture is from a real patient. That gap is exactly where we work. At SurgeonsLab, we build simulation models that look, feel and behave like real anatomy. That means tissue with realistic feel, vessels with physiological flow, and anatomy that responds the way your device will meet it in the clinic. Device teams work with us across the whole product lifecycle: • R&D and early design iteration • Bench testing and design verification • Human factors and usability studies • Physician training and procedural education • Sales enablement and live demos that actually show your device in action Whether you're working on a Class I instrument or a Class III implant, we can build around your device, your procedure and your target anatomy, including patient-specific models from imaging data. At the booth you'll get hands-on time with: Surgical Spine Model Vascular & Tumor Model Reusable Embolic Demonstrator (RED) CathTrain VR endovascular simulator Endovascular flow models with Circle of Willis aneurysms What we'd most like to hear about is the procedure you're struggling to test, teach or demo. Bring it to us and let's talk about building it. Flying in from the East Coast or elsewhere? Send me a message and we'll set a time to meet so you're not hunting for us on the show floor. Booth #2946, Minneapolis Convention Center October 28–29, 2026 #MDMMidwest #MedTech #MedicalDevices #MedicalSimulation #DeviceDevelopment #InterventionalRadiology #Endovascular #Neurovascular #SpineSurgery #HumanFactors #MedicalAlley #SurgeonsLab

Getting the embolic in is the easy part. The real question is where it goes next. In MMA embolization, "how distal is distal enough?" has become one of the most debated questions in the field. Go deeper and you may cover more of the target territory. Push too hard and you risk reflux back along the catheter, or flow into places you never meant to reach. The tricky part is that a lot of this happens in vessels smaller than a millimeter, where it's hard to see what's actually going on. So we filmed it. This video is live fluoroscopy of a liquid embolic moving through our MMA model, with branches in the sub-millimeter range. You can watch two things happen in real time: 1. How far the embolic penetrates into those small distal branches 2. When reflux starts, and how far it travels back toward the catheter tip Because the anatomy is the same every run, you can change one thing (injection speed, catheter position, the agent itself) and see exactly what that change does. For physicians, that means practicing the feel of a controlled injection before it matters. For device teams, it means comparing how an agent or catheter behaves in a consistent, repeatable anatomy. Watch it, and tell us: what would you test first? #MMAembolization #Neurointervention #Embolization #Endovascular #InterventionalNeuroradiology #MedicalSimulation #MedTech #SurgeonsLab

Evaluating embolic penetration and reflux dynamics requires bridging direct bench-top observation with real-world clinical imaging. The Reusable Embolic Demonstrator (RED) provides a single, flow-enabled platform supporting three distinct visualization modalities: Optical Camera: Real-time, transparent tracking of vessel filling, reflux patterns, and occlusion mechanics. Fluoroscopic: Seamless integration for embolic tracking and workflow evaluation in an angio suite CT road mapping: High-resolution cross-sectional computed tomography imaging for detailed 3D volumetric assessment. Pairing quick-swap pathology modules with multi-modal compatibility gives R&D and clinical teams a cost-controlled setup to validate embolic behavior from benchtop to angio suite. Know more about the Reusable Embolic Demonstrator, visit surgeonslab.com/reusable-emb… You can also drop us an email at [email protected] #Endovascular #Neuroradiology #LiquidEmbolics #SurgeonsLab #MedicalDeviceTesting #Neurointerventions