Kryptovalas🐋

Happy Uptober! 🍂🚀 2021: +40% 🟢 2022: +6% 🟢 2023: +29% 🟢 2024: +11% 🟢 2025: -4% 🔴 2026: Paljonko?

太牛批了。刚刚字节跳动旗下的懂车帝，发布了对华为尊界 V800 的紧急刹车评测视频，就是那台售价 88、101 万，后排有冰箱、能沏咖啡的商务车。 结果几台车，好几次测试，都出现了踩紧急刹车，刹车踏板直接断了。。现在评论区都在刷屏，这视频什么时候被公关下架。

Bitcoin vs kulta: 5 vuotta soutamista ja huopaamista 🛶 Onko bitcoinin vuoro ylisuoriutua?

Croatia is joining as the eighth country in Europe to approve FSD Supervised. 🇭🇷 🇳🇱 Netherlands - 10 April - 4.02% 🇱🇹 Lithuania - 20 May - 0.64% 🇪🇪 Estonia - 29 May - 0.3% 🇩🇰 Denmark - 9 June - 1.32% 🇧🇪 Belgium - 10 June - 2.63% 🇸🇮 Slovenia - 7 September - 0.47% 🇨🇿 Czech Republic - 21 September - 2.42% 🇭🇷 Croatia - 29 September - 0.86% Croatia will add another 0.86% of the EU population to the vote. This increases the proportion of yes voters to 12.66% of 65%.

AGENT WARS We asked 5 top AI models to design, engineer and 3D print a bridge to with the goal of holding the most possible weight. 🇺🇸 Anthropic: Claude Opus 5.5 (High) 🇨🇳 Kimi: Kimi K3 (High) 🇺🇸 Meta: Muse Spark 1.3 (High) 🇺🇸 OpenAI: GPT 6 Astra (High) 🇺🇸 SpaceXAI: Grok 4.7 (High) Each bridge had specific parameters. It had to span 2 feet, use a maximum 500 grams of filament, and it had to be under 18 hours of printing time. We specified what type of weight and where we would place it on the bridge. The Score: • Claude Opus 5.5 held an estimated 130 lbs! It took 9 hours and 11 minutes to print 17 parts and used 441 grams of filament. • Meta Muse Spark 1.3 held 26.5 lbs. It took 13 hours and 12 minutes to print 49 parts and used 478 grams of filament. • OpenAI GPT-6 Astra held an estimated 17.5 lbs. It took 15 hours and 44 minutes to print 29 parts and used 442 grams of filament. • SpaceXAI Grok 4.7 did not finish. On assembly it could not stand up by itself. It took 12 hours and 22 minutes to print 29 parts and used 460 grams of filament. • Kimi K3 did not finish. It wasn’t engineered correctly so the bridge could not even be assembled. It took 11 hours and 19 minutes to print 35 parts and used 446 grams of filament. That means our champion for this episode is Claude Opus 5.5. Not only did it hold the most weight (by FAR) it also took the least time to print, used the least amount of parts and used the least amount of filament. This was episode 02 of Agent Wars, stay tuned for episode 03.

I don't care what your politics are, this landing is pure butter.

Introducing Claude Opus 5.5, the first model in our new Claude 5.5 family. It performs at the level of Claude Fable 5.1 for most tasks, and costs 40% less to run than Opus 5.